收藏本站
SSI Technologies – Application Note PS-AN7
MediaGauge? (Model MG-MD) Digital Pressure Gauge
Product Overview
To set the High or Low pressure set points: Press and hold
down the UNIT/SET button for 3 seconds. The
MediaGauge? MG-MD will go into the pressure setting
mode.
Electrical Interface
MediaGauge? MG-MD harness connections:
1) The screen shows
on the top, left hand side
White wire:
Power Lead for supply input (12 Vdc)
indicating high pressure setting, and the first digit
will be flashing.
Black wire:
Return Lead
2) Set the first digit value by pressing the
(select from 0 to 9). Then press the
Button
Button,
Brown wire:
Limit Switch output (NPN Transistor output)
which shifts to the second digit. Again use the
Blue Wire:
4-20 mA output for meter. (Must be loop
Button to select 0 thru 9 followed by the
to complete the third and forth digits.
Button
grounded with black wire)
3) After all 4 digits of the high pressure settings are
done press the
screen will show
Button one more time, the
on the top, left hand side
Typical Wiring Interface
indicating low pressure setting. Repeat steps 1 and
2 above to set the 4 digits of the low pressure
settings.
4) After all 4 digits of the low pressure settings are
done press the Button one more time, the
screen will show “Load”, indicating your pressure
settings have been saved into memory.
This is a description of an application to interface the
MediaGauge? MG-MD to a monitoring and control system
utilizing the limit switch output to control a relay and monitor
the output current. The relay will turn on and off based
upon the high and low pressure set points the user
programs into the MediaGauge? MG-MD digital pressure
gauge.
5) To make sure that the settings are correct, you can
press the
Button to check the value of the low
1) Mount the MediaGauge? MG-MD digital pressure
pressure setting and press the Button to check
the value of the high pressure setting.
gauge on a suitable (1/4” NPT) female fitting. Use
Teflon tape or pipe dope to seal the threads. . Do
not over tighten. Torque to 150 in lbs +/- 1 in lb.
2) Connect the supplied mating harness with Din
connector to the mating connector on the back of
the MediaGauge? MG-MD digital pressure gauge.
3) Program the MediaGauge? digital pressure gauge
with your low and high pressure set points per the
instructions described previously.
SSI TECHNOLOGIES, INC.
Controls Division
2643 West Court Street
Janesville, WI 53548-5011
Phone: (608)758-1500
Fax: (608)758-2491
Copyright January 30, 2009
SSI Technologies Inc.
All Rights Reserved
Revision 4
www.ssitechnologies.com
5
RoHS
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
MG1-1000-A-9V-R SENSOR DIGITAL GAUGE 1000PSI LCD
MGA-300-A-9V-R SENSOR DIGITAL GAUGE 300PSI LCD
MGSF1N02LT1 MOSFET N-CH 20V 750MA SOT-23
MGSF1N03LT1 MOSFET N-CH 30V 1.6A SOT-23
MGSF2N02ELT1G MOSFET N-CH 20V 2.8A SOT-23
MH805 COPYHOLDER 36" INTERNAL 12"X10"
MIC2807-OOYML TR IC PWR MANAGEMENT RF PA 17-MLF
MIC2808-NNYFT TR IC RF PA SOLUTION 600MA 16-FTMLF
相关代理商/技术参数
MG-500-A-9V-R 功能描述:SENSOR DIGITAL GAUGE 500PSI LCD RoHS:是 类别:传感器，转换器 >> 压力 系列:MG-9V 标准包装:100 系列:*
MG-500-A-MD-R 功能描述:SENSOR DIGITAL GAUGE 500PSI LCD RoHS:是 类别:传感器，转换器 >> 压力 系列:MG-MD 标准包装:100 系列:*
MG-500-B-MD-R 功能描述:SENSOR 500 PSI 4-20 MA 1/8 NPT RoHS:是 类别:传感器，转换器 >> 压力 系列:MG-MD 标准包装:100 系列:*
MG500-NISTL 制造商:Extech Instruments Corporation 功能描述:HIGH VOLTAGE INSULATION TESTER WITH LIMITED NIST
MG500Q1US1 制造商:n/a 功能描述:IGBT Module
MG500Q1US11 制造商:n/a 功能描述:MG500Q1US11
MG500Q1US2 制造商:Toshiba America Electronic Components 功能描述:
MG-5020JE 制造商:EPSONTOYOCOM 制造商全称:Epson ToYoCom 功能描述:CRYSTAL OSCILLATOR